OmniScan^™ X3 64 Phased Array and TFM Flaw Detector with Advanced Capabilities

Power You Can Carry

Housed in the field-proven rugged and portable OmniScan X3 enclosure, the OmniScan X3 64 flaw detector’s powerful focusing capabilities supported by its larger element-aperture capacity enable you to fully exploit 64-element phased array probes and 128-element aperture TFM. Utilize its enhanced performance to meet the inspection challenges of thick and attenuative materials and expand your potential to develop new procedures for a wider range of applications.

Download the OmniScan X3 64 Brochure

WeldSight™ Advanced Analysis Software

OmniScan^™ X3 Phased Array Flaw Detector with Innovative TFM

Confidence You Can See

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, including total focusing method (TFM) imaging and advanced visualization capabilities, backed by its high image quality enable you to complete your inspection with greater confidence.

Download the OmniScan X3 Brochure

Innovative and Efficient TFM

Confirm Your TFM Beam Coverage in Advance

The Acoustic Influence Map (AIM) tool provides you with an instant visual model of the sensitivity based on your TFM mode, probe, settings, and simulated reflector. The AIM tool takes the guesswork out of creating your scan plan—visualize the effect of a wave set (TFM mode), see where sensitivity stops, and adjust your scan plan accordingly.

See What You’ve Been Missing with PCI

Our innovative amplitude-free live phase coherence imaging (PCI) improves small-defect sensitivity and penetration in noisy materials, all while easing your setup and simplifying sizing. Available on the OmniScan X3 64 flaw detector as of MXU 5.10.

Virtual Collaboration, Virtually Anywhere

The X3 Remote Collaboration Service (X3 RCS) enables you to share your screen, allow a remote collaborator to control the unit, and host a video conference with participants located almost anywhere in the world.

Improved, Faster Calibration

The OmniScan X3 calibrator tracks the signals at high speed. Perform multigroup calibrations in minutes.

Familiar Yet Improved OmniScan Experience

Users who own or trained on an OmniScan will transition easily to the OmniScan X3 flaw detector, and new users will find it easy to learn.

Reveal More Details

Benefit from 64-Pulser Phased Array

Exploit the full potential of 64-element phased array probes using the OmniScan X3 64 flaw detector to achieve improved resolution at the focal point.

Acquired using a 32-channel OmniScan X3 unit with a 64-element probe (5L64-A32 model), this S-scan is a high-quality image but the resolution reflects the fact that only the middle 32 elements could be used for the focal law.

Using a full 64-element aperture (5L64-A32 probe), the OmniScan X3 64 flaw detector provides better PA resolution at the focal point, enabling you to more easily distinguish indications that are close together or in a cluster.

Access Full 128-Element Aperture TFM

Made possible by new generation electronics, TFM imaging offers better focusing capabilities for smaller indications and an improved signal-to-noise ratio (SNR). With its 128-element aperture capacity, the OmniScan X3 64 model provides enhanced image clarity.

This TFM image was acquired with 64 elements of a 128-element probe (3.5L128-I4 model) using an OmniScan X3 32-channel model.

Here, the OmniScan X3 64 flaw detector enabled us to use the full 128-element aperture of our 3.5 MHz, 128-element I4 probe. Note the improved resolution and reduced background noise.

Acquire up to 4X Faster TFM

Achieve total focusing method (TFM) acquisition speeds of up to 4 times faster when using a 64-element probe. Compared to other models with 32 pulsers, the OmniScan X3 64 flaw detector offers a significant improvement in efficiency owing to its larger aperture capability.

Improved Phased Array

Up to 3x as fast as the OmniScan MX2 flaw detector (max pulse repetition frequency)
Single TOFD menu for an accelerated calibration workflow
800% high amplitude range reduces the need to rescan
Onboard Dual Linear Array™ and Dual Matrix Array™ probe support accelerates setup creation

Ease Corrosion Monitoring Using Phased Array

Using phased array to inspect corrosion offers many benefits, including excellent coverage and resolution. However, becoming proficient in phased array techniques can be challenging. The OmniScan X3 flaw detector combines advanced functions such as gate synchronization with thoughtfully designed software and simplified menus, so you can obtain accurate data more easily. Configure your setup quickly thanks to its A-scan synchronization processing and manual time-corrected gain (TCG).

OmniScan X3 Series

Service and Support You Can Trust

From calibration to training, we offer a broad portfolio of services to help you maintain optimal device performance. Evident service contracts are:

Straightforward—so you can focus on the core of your business
Efficient—we can schedule preventative maintenance, including calibrations, on your behalf
Cost-effective—providing you savings throughout the life of the contract